Mon - Fri, 8:00 - 9:00



Schreiben Sie uns eine E-Mail

[email protected]

LoRaWAN Gateway and Wireless Sensor Catalog


SenseCAP is an industrial wireless sensor network that integrates easytodeploy hardware and data API services, enabling lowpower, longdistance environmental data collection.

RX9 Simple | EXSEN (Carbon Dioxide Gas Sensor)


RX9 Simple | EXSEN (Carbon Dioxide Gas Sensor) RX9 Simple. Indoor. Smallest. Gas Concentration Step output. Gas Concentration step (LEVEL) output. No ppm. Cost Effective. 2 ADC Required.

Masimo ISA Capnography CO2 Sidestream Gas Analyzer Kit ...


Product Description. The Root® patient monitoring and connectivity platform is expandable with the ISA™ CO2 module for your capnography monitoring needs. Displays endtidal carbon dioxide (EtCO2) waveform and measurements and trends of EtCO2, fractional concentration of inspired carbon dioxide (FiCO2), and respiration rate (RR) Indicated for ...

Intelligent Infrared CO2 Module (Model: MHZ19B)


The sensor should be away from heat, and avoid direct sunlight or other heat radiation. Do not use the sensor in the high dusty environment for long time. To ensure the normal work, the power supply must be among ~ DC rang, the power current must be not less than 150mA.

Homemade CO2 Sensor Unit


We can start with setting up the SCD30 CO2 Sensor Module, note that we are only using the four pins shown in the following figure 2 (VDD, GND, TX/SCL and RX/SDA): Figure 2 SCD30 Sensor pins used Next, we can set up the BME280, here we will be using again only the four pins on the left side (GND, , SDA and SCL) referring to figure 3.

Measure CO2 Levels With Ardunio and K30 Sensor : 9 Steps ...


The K30 is an nondispersive infrared (NDIR) CO2 sensor. Unlike electrochemical CO2 sensors, NDIR sensors use light to measure the wavelength of CO2 molecules. Electrochemical sensors last a few years. With normal care, the K30 will last upwards of 15 years. Click here to …

CO2 Safety System Logico2


Installation of the CO2 Sensor The CO2 sensors (Mk9 or Mk10) should be installed at a maximum height of 30 cm/ 12” from the floor and maximum 5 m/16,4 ft away from the CO2 distribution point. The sensors cover an area of maximum 78 m2/840 ft2. Try to find an installation position where the unit is …

CelCulture® CO2 Incubator | Esco Medical


CCL170B9IVF. CelCulture ® Incubator 170L IR Sensor, CO2 Control ULPA, Moist Heat Decon, with Sealed Inner Door Kit for 170L (4 Glass Doors With Latches), Factory Installed, 115VAC 50/60Hz. 2170279. CCL240B9IVF. CelCulture ® Incubator 240 L, IR Sensor, CO2 Control, ULPA, Moist Heat Decon, with Sealed Inner Door Kit for 240L

MODEL RX-516 RX-517 LEL, PID, H2S, CO, O2 Sensors


RX516/RX517 this time. This instrument is an explosionproof type portable gas detector which is designed to measure the presence of the following gas at crude oil

GitHub crisap94/MHZ19: MHZ19 CO2 sensor library for ...


14/12/2020· Include this library to your Arduino IDE. Wiring MHZ19 sensor to your Arduino or ESPWROOM02/32 (ESP8266/ESP32). MHZ19 Vout to Arduino Vout (5V) MHZ19 GND to Arduino GND. MHZ19 Tx to Arduino Digital Pin (Serial Rx pin) MHZ19 Rx to Arduino Digital Pin (Serial Tx pin) other MHZ19 pins are not used. Wiring the MHZ19 through PWM use a PWM ...

UART and Raspberry Pi Pico (RP2040) MicroPython Forum


23/2/2021· """initializes communication with CO2 sensor""" = UART(uartNum, 9600) (parity=None, stop=1, bits=8, rx=rxPin, tx=txPin) wait a minimum amount of time before trying to read the sensor sleep_ms(250) def readCO2(self): """reads CO2 concentration from MHZ14a sensors and returns ppm value"""

Intelligent Infrared CO2 Module (Model: MHZ19)


MHZ19 NDIR CO2 Module 1. Profile MHZ19 NDIR infrared gas module is a common type, small size sensor, using nondispersive infrared (NDIR) principle to detect the existence of CO 2 in the air, with good selectivity, nonoxygen dependent and long life. Builtin temperature sensor can do temperature compensation; and it has UART output and PWM ...

AMUN 716 SR | CO2 sensors | Sensor technology | Climate ...


Function description. Suitable for conference and meeting rooms, offices, schools/nurseries, passive and lowenergy housing. Power unit optionally available. Power unit is suitable for flush mounted installation. 2 switch outputs CO2 controlled for 2 stage control, with manual and automatic mode as well as display of switching status.

Hinterlasse einen Kommentar